| Analog Mode Specifications |
| Vertical Deflection (PM 3380B/90B) |
| Input Channels: |
2 Channels + Ext Trig View |
| Frequency Response: |
100 MHz |
| Deflection Coefficient: |
Ch1 & Ch2 (all models): 2 mV/div . 5 V/div in a 1-2-5 sequence or 2 mV/div to 12.5 V/div calibrated continuously variable |
| Rise Time (Calculated): |
1.75 ns |
| Error Limit: |
1.3% (Measured over center 6 divisions)
|
| Input Impedance: |
(all models, all channels) 1 MΩ Â±1% // 25 pf ±2 pf
|
| Max. Rated input voltage: |
In 1 MΩ position: 150 Vrms CAT II |
|
In 50Ω position: 5 Vrms; 50V ac peak ( max of 50 mJ during any 100 ms interval.
|
| | Vertical Deflection (PM 3384B/94B) |
| Input Channels: |
4 Channels |
| Frequency Response: |
200 MHz
|
| Deflection Coefficient: |
Ch1 & Ch2 (all models): 2 mV/div . 5 V/div in a 1-2-5 sequence or 2 mV/div to 12.5 V/div calibrated continuously variable
|
|
Ch3 & Ch4 (PM 3384B/94B): 2 mV/div . 5 V/div in a 1-2-5 sequence or 2 mV/div to 12.5 V/div calibrated continuously variable
|
| Rise Time (Calculated): |
1.75 ns
|
| Error Limit: |
1.3% (Measured over center 6 divisions)
|
| Input Impedance: |
(all models, all channels) 1 MΩ Â±1% // 25 pf ±2 pf
|
|
(PM 3390B/94B): user selectable 50Ω Â±1%
|
| Max. Rated input voltage: |
In 1 MΩ position: 150 Vrms CAT II
|
|
In 50Ω position: 5 Vrms; 50V ac peak ( max of 50 mJ during any 100 ms interval.
|
| | Horizontal (Main & Delayed Timebases) |
| Display Modes: |
Main Timebase (MTB), Delayed Timebase (DTB), Alternate Timebase ( MTB & DTB), X-Y Mode. |
| Time Coefficients: |
(PM 3380B/3384B): 0.5 s/div to 50 ns/div in a 1-2-5 sequence or calibrated variable control, 1.25 s/div to 50 ns/div. |
|
(PM 3390B/3394B): 0.5 s/div to 20 ns/div in a 1-2-5 sequence or calibrated variable control, 1.25 s/div to 20 ns/div.
|
| Fastest Sweep (Magn 10X): |
(PM 3380B/3384B) 5 ns/div |
|
(PM 3390B/3394B) 2 ns/div |
| Error Limit (Magn 10X):
|
±1.3% of reading + 0.5% of 8 divisions) |
| | Triggering (Main & Delayed Timebase) |
| Trigger modes: |
Auto free run, Triggered, Single, Edge Triggering, TV Triggering
|
| | Edge Triggering |
| MTB Trigger Source: |
(PM 3380B/3390B): Ch1, Ch2, Ext |
|
(PM 3384B/3394B): Any input channel or Line (mains);
Optional rear mounted External Trigger input replacing line Triggering. |
| DTB Trigger Source: |
Starts after delay or triggered on any input channel.
|
| Slope: |
Positive or Negative
|
| Coupling: |
DC, AC (> 10 Hz), LF-Rej (30 kHz), HF-Rej (30 kHz)
|
| Level Range: |
±8 div or level within signal peak to peak range.
|
| Level Indication:
|
On screen level indicators and numeric readout. |
| Trigger Sensitivity: |
(PM 3380B/3384B): 0.6 div up to 50 MHz, 1.2 div up to 100 MHz, 2.0 div up to 200 MHz |
|
(PM 3390B/3394B): 0.6 div up to 100 MHz, 1.2 div up to 200 MHz, 2.0 div up to 300 MHz
|
| | TV Triggering |
| Video Standard: |
HDTV, NTSC, PAL, SECAM standards |
| MTB Trigger Source: |
CH1 to CH4, Field1, Field2, TV-Lines
|
| Signal Polarity: |
Positive or Negative
|
| Sensitivity: |
0.7 div (Sync Pulse)
|
| | Cursor Measurements |
| Cursor Modes: |
Horizontal, Vertical, Both
|
| Readout: |
Vertical: dV, V1 to gnd, V2 to gnd, Ratio
|
|
Horizontal: dt, 1/dt (in Hz), Ratio, Phase |
| Accuracy (magn 1X): |
1% of full scale within the central 8 horizontal and 6 vertical divisions. |
| | X-Y Mode |
| X Deflection Source: |
Any input channel or line |
| X Deflection Coefficient: |
Same as for vertical deflection
|
| Dynamic range: |
20 div up to 100 kHz, > 10 div up to 2 MHz.
|
| Frequency Response: |
32 MHz at -3 dB
|
| Error Limit: |
5% measured over central 6 divisions.
|
| Phase Shift: |
< 3o up to 100 kHz
|
|
| Digital Mode Specifications |
| Acquisition |
| Repetitive Sample Rate: |
Random sampling gives an equivalent sample rate of up to;
|
|
(PM 3380B/3384B): 10 GS/s |
|
(PM 3390B/3394B): 25 GS/s |
| Single Shot Sample Rate: |
Up to 200 MS/s |
| Vertical resolution: |
ADC resolution: 8 bit |
|
Memory resolution: 16 bit |
| Memory: |
(PM 3380B/3390B): Standard Memory: 8 k, max trace storage, 27 traces |
|
(PM 3380B/3390B): Extended Memory option: 32 k, max trace storage, 153 traces |
|
(PM 3384B/94B): Standard Memory: 32 k, max trace storage, 204 traces
|
| Average:
|
2,4,8 to 4096, giving a resolution of up to 14 bits |
| Peak Detection: |
Captures glitches up to 5 ns |
| Envelope Mode:
|
For continuous tracking of changing waveforms
|
| | Vertical |
| Auto Ranging vertical deflection: |
Automatically and continuously adapts the instrument's vertical settings to have 2 to 6 divisions' display of input signal. |
| Bandwidth: |
See above analog mode specification
|
| Magnification: |
Up to x32 magnification for higher deflection sensitivity.
|
| Display modes: |
Ch1, ± Ch2, Ch3, ± Ch4, calculated add and subtract |
| Window Mode: |
2 or 4 windows to display two or four traces above each other while using the full dynamic range of the ADC
|
| | Horizontal |
| Autoranging timebase: |
Continuously adapts timebase sweep speed to the frequency of the trigger signal in order to keep 2 to 6 cycles on screen.
|
| Acquisition modes: |
Recurrent (Auto and triggered), Single Shot, Multiple Single Shot, Roll, Triggered Roll |
| X-Y Mode: |
Any trace in memory or any of the input channels can be used as a X source.
|
| | Timebase |
| Single Shot Sampling:
|
200 s/div to 500 ns/div in a 1-2-5 sequence |
| Variable Timebase: |
Continuously variable sweep speed; 1us/div to 500 us/div in 1 us increments. 500 us/div to 200 s/div with 0.2% or smaller increments. |
| Recurrent:
|
(PM 3380B/3384B): 200 ns/div to 5 ns/div
|
|
(PM 3390B/3394B): 200 ns/div to 2 ns/div |
| Roll Mode: |
200 s/div to 200 ms/div, triggered or free roll mode, in a 1-2-5 sequence or continuously variable
|
| Display Resolution: |
Horizontal resolution for 1x magnification: 500 samples = 10 divisions = 1 screen width. |
| Magnification: |
x2, x4 to x32 to zoom in onto parts of waveform |
| Interpolation: |
Dots, Sine or Linear |
| | Triggering |
| Trigger Coupling: |
Same as analog mode
|
| Edge Triggering:
|
Same as analog mode plus; dual slope triggering available when in single shot, real time mode.
|
| TV Triggering: |
Same as analog mode
|
| Logic trigger modes: |
(PM 3380B/3390B): Glitch (time qualified pulse) |
|
(PM 3384B/3394B): State (4 bit), Pattern (4 bit), Glitch (time qualified pulse)
|
| | Delay |
| Time Delay: |
0 to 1,000 div continuously adjustable |
| Pre trigger view: |
Up to a complete record can be filled with pre-trigger information. (160 div for 8 k, 640 division for 32 k)
|
| Event Delay: |
1 to 16,384 events, max count rate 50 MHz |
| Delay Modes: |
Starts after time delay or wait for trigger after time delay. |
| | Cursor Measurements |
| Cursor Modes: |
Horizontal, Vertical, Both: Free or locked to trace |
| Readout: |
Vertical: dv, V1 to gnd, V2 to gnd, Ratio |
|
Horizontal: dt, 1/dt (in Hz), Ratio, Phase (cycle is automatically referenced to trigger signal)
|
| | Calculated Measurements |
| Volt: |
DC, rms, minimum, maximum, peak to peak, Low level, High level, Overshoot (positive & negative), Pre-shoot (positive & negative) |
| Time: |
Frequency, Period, Pulsewidth, Rise time, Fall time, Duty cycle
|
| Delay: |
Channel to channel, rising and falling edges.
|
| Quick Measurements |
Probe operated, "Touch Hold And Measure" instantly gives calculated measurements of frequency, dc, rms, and Vp-p. |
| | Processing |
|
Add, Subtract, Multiply, Digital Filter, Integrate, Differentiate, FFT, Histogram, Pass Fail. |
|
| General Specifications |
| Autoset |
|
Selects proper channel, time-base and trigger settings. Function can be customized |
| | Autocal |
|
Automatic fine adjustment for enhanced accuracy to get optimal performance even under extreme environmental conditions |
| | Interfacing |
| Standard: |
RS-232C, CPL protocol
|
| Options: |
IEEE-488.2(GPIB), SCPI |
| | Hard Copy |
| Output: |
Printed or plotted hard copy of the screen in digital mode.
|
| User Text: |
Two lines of on-screen text |
| Interface: |
RS-232C or IEEE-488.2 (GPIB)
|
| Printer Drivers: |
FX Series (9 Pin), LQ1500 (24 Pins), HP 2225 Thinkjet, HP Laserjet, (series II & III), HP 540 Deskjet, and compatibles. |
| Plotters: |
HP 7440, HP 7550, HP 7475A, HP 7470A and compatibles, HPGL.
|
| Camera: |
Camera Kit PM 9381/001 available as optional accessory.
|
| | Power Supply |
| Line Voltage: |
100V to 240V (±10%) CAT II
|
| Line Frequency: |
50 Hz to 400 Hz (±10%)
|
| Power Consumption: |
115W (130W with all options installed)
|
| | Safety |
|
Meets requirements of EN 61010-1 CAT II Pollution Degree 2, Low Voltage Directive 73/23/EEC, UL3111, CSA C22.2 No 1010-1 |
|
Meets requirements of MIL-STD-461C: Part2 CEO1 (narrow band), Part4 CEO3, Part2 CSO1, Part5 CSO6, (Limited to 300V), Part5 and 6 REO1, Part2 REO2 (max. 1 GHz) |
| | EMC |
| | Miscellaneous |
| Setting Memory: |
10 complete instrument setups, with battery backup.
|
| Calibrated output: |
600 mv p-p, 2 kHz square wave.
|
| Z-Modulation Input: |
BNC, 10 kΩ > 2.4V=blanked, < 0.5 V=unblanked
|
| Time Between Calibration: |
2000 Hrs or 1 year |
|
4000 Hrs or 2 year if error limits are doubled. |
| | Size (excluding handle & feet) |
|
139 mm H x 341 mm W x 481 mm L |
|
5.5" H x 13.4" W x 18.9' L |
| | Weight |
| | Warranty |
|
Three-year product warranty, parts and labor. Five year CRT warranty. |
|
|